How to Design and Implement Project Enterprise Network (Full Video)
Tagged on:                                                                                                                                                             

20 thoughts on “How to Design and Implement Project Enterprise Network (Full Video)

  • May 30, 2019 at 5:55 pm
    Permalink

    Hello please can you send me this project

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    Assign ip on ISP ????? or empty,,please say

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    sir you can help me to make a project of ccn ,

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    your video is very informative i hope if you can send me the pkt file for details thanks lot

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    plz mail me its configuration and .pkt file. i wnat to work on dis project
    and i follow you on facebook. i didn't get the pkt file

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    There is problem with standby command on PacketTracer ( invalid ) please help

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    (Please send me the LAP and no one as much as this project works on this email ( [email protected]

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    please!
    can you send the packet tracer file?
    to my email!!
    please

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    sir I want to pkt file .I am working this project

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    plz send me the .pkt file of this project

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    You had a lot of mix ups and glitches in the video, like forgetting to set ASW1 Fa0/1 and Fa0/2 to trunk mode in the beginning and then deleting a lot of components and the vlan.dat files and reload to try to correct it. You also programmed the wrong interfaces on Etherchannel, and at 1:45:45 you are supposed to click "Auto Capture/Play" to run the packet tracer simulation. With that said, I did learn a lot and still thumbed up your video. Good job and try to keep it more condensed with clearer English next time. Thank you!

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    I have added you on fb. Can you please send to me its configuration and .pkt file too at [email protected] Many Thanks

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    Sir i liked your video its very helpful
    i send a friend request to you and a request to join the group
    Please can you send me the .pkt files it will save my life:
    [email protected]
    Thank you so much

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    could u please mail me the project with documentation and pkt file

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    Excellent video. sir please can you send me the .pkt file??

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    What was the configuration on DPLC???

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    Hi, is not the etherchannel supposed to be a trunk? On core sw 1 you selected int fa0/21-14 instead of 21-24. The port channel formed only for int fa0/21. After configuring core sw 2 int fa0/21-24 you verified the etherchannel summary, but did not check for the formation of trunking between the 2 core switches. Is this a problem? I have constructed the network as per your design and working thru the whole configuration. Kindly revert. Thanks.

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    Hi, thx for your project. I add your page on facebook, but i don't see the packet tracer file or the exercice formulation. is it possible to have it? thanks a lot

    Reply
  • May 30, 2019 at 5:55 pm
    Permalink

    good try but your design is flawed or missing some other parts from a full cisco enterprise network modules. there is no DMZ zone, teleworker worker, wan module, remote datacenter, and you seem to confute data center and DMZ servers, your design doesn't have services section.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *